Dromida DB4.18 Assembly Guide Bedienungsanleitung PDF herunterladen

HELPFUL HINTS

✔ Avoid working over a deep pile carpet. If you drop a small part or screw,

it may be difficult to find.

✔ Place a mat or towel over your work area. This will prevent parts from rolling off and will protect the work surface.

✔ Avoid running the car in cold weather. The plastic and metal parts can become brittle at low temperatures. In addition, grease and

oil become thick, causing premature wear and poor performance.

MAINTENANCE

BEFORE EACH RUN

✔

IMPORTANT: Check to make sure that all

screws are tight. Check that the servo

saver screw is fully tightened to ensure

that your Dromida DB4.18 tracks straight.

✔ Always check the condition of your

radio system batteries and replace if

necessary.

✔ Check to make sure that all of the

moving parts of the Dromida DB4.18

move freely and do not bind.

✔ Turn on the radio and make sure the

servo moves easily and in the proper

direction.

✔ Check for any broken or damaged

parts. Replace them before running the

Dromida DB4.18. Running the Dromida

DB4.18 with broken or damaged parts

could damage additional parts.

✔ Check to make sure that all wires are

properly connected.

AFTER EACH RUN

✔ Clean any debris from the chassis and

moving parts.

✔ Check for any broken or damaged parts.

Replace them before the next run.

✔ Disconnect and remove the battery

from the chassis.

AFTER EVERY 10 RUNS

✔ Check to make sure that the bearings

are free of dirt and debris, and roll

smoothly.

✔ Check the shocks for oil leakage.

✔ Check the tires to make sure they are

still properly glued to the rims.

ASSEMBLY AND MAINTENANCE GUIDE

HARDWARE CHART

2x10MM FLAT HEAD SCREW

2x4MM ROUND HEAD SCREW

2x8MM FLAT HEAD SCREW

2x8MM ROUND HEAD SCREW

2x10MM ROUND HEAD SCREW

6x10MM BALL BEARING

8x12MM BALL BEARING

2x8MM ROUND HEAD

SHOULDER SCREW

3x3MM SET SCREW

3MM LOCK NUT

2.6x5MM WASHER

3x6MM WASHER

2x6MM SELF-TAPPING

ROUND HEAD SCREW

2x12MM SELF-TAPPING

ROUND HEAD SCREW

2x15MM SELF-TAPPING

ROUND HEAD SCREW

2x5MM SELF-TAPPING

ROUND HEAD SCREW

2x14MM FLAT HEAD SCREW

2.5x8MM FLAT HEAD SCREW

2.5x8MM SOCKET HEAD SCREW

2.5x14MM SOCKET HEAD CAP SCREW

3x6MM SOCKET HEAD SCREW

3x6MM SELF-TAPPING

BUTTON HEAD SCREW

3x8MM SELF-TAPPING

BUTTON HEAD SCREW

2.5x5MM BUTTON HEAD

SCREW

BODY CLIP

1.5MM E

CLIP

ACTUAL SIZE

(

WHEN PRINTED AT 100%

)

™

1 2 3 4 5 6 ... 11 12

Inhaltsverzeichnis

Seite 1 - HARDWARE CHART

HELPFUL HINTS ✔ Avoid working over a deep pile carpet. If you drop a small part or screw,it may be difficult to find.✔ Place a mat or towel over you

Seite 2 - 2. DIFFERENTIALS TO CHASSIS

18. SIDE BODY PANEL INSTALLATION 8789AAAAAAYYYYYYYYYY8688AA17. WHEELS 707070RDDR

Seite 3 - 4. CENTER SHAFT

8485YYYYYYY19. TOP BODY PANEL INSTALLATION

Seite 4 - 6. MOTOR MOUNT

TUNING GUIDE When tuning the Dromida DB4.18 make sure that you have equal lengths from one side to the other on the shocks and upper rods. Also, make

Seite 5 - 8. REAR SUSPENSION

313332333032GGBGGB34GREASEGREASEGREASEGREASENOTE DIRECTIONNOTE DIRECTION221HHHH1. DIFFERENTIAL ASSEMBLY 2. DIFFERENTIALS TO CHASSIS

Seite 6 - 10. SHOCK ASSEMBLY

3. STEERING ASSEMBLY 4. CENTER SHAFT 1845184040444046PPDO NOT OVERTIGHTEN(WILL CAUSE BINDING)DO NOT OVERTIGHTEN(WILL CAUSE BINDING)28292728ABAGREASEGR

Seite 7 - 12. FRONT SHOCK INSTALLATION

5. SHOCK TOWERS 73871128403740404011GGEEEVVENOTE DIFFERENCENOTE DIFFERENCENNTKQKTEEEEEE392642524THREADLOCKTHREADLOCK6. MOTOR MOUNT

Seite 8 - 14. FRONT BUMPER

7. FRONT SUSPENSION 8. REAR SUSPENSION 414241433815403635371718BBDO NOT OVERTIGHTENFULLY SEAT BEARINGSDO NOT OVERTIGHTEN940LCH401314HLACTUAL SIZE11.2M

Seite 9 - 16. CAGE INSTALLATION

GGG9. ELECTRONICS 10. SHOCK ASSEMBLY 564050515249474748XSFXSCREW MUST BE SNUGCENTER SERVO FIRST7.5MMACTUAL SIZESHOCK OILSHOCK OILSHOCK OIL585562625966

Seite 10 - 17. WHEELS

11. REAR SHOCK INSTALLATION 12. FRONT SHOCK INSTALLATION 53SM53SM

Seite 11

13. REAR BUMPER 14. FRONT BUMPER EE2374EBBBBEBBBB201921EEEEEE

Seite 12 - TUNING GUIDE

15. CAGE ASSEMBLY 82767775928081797891AAZZAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA8391839090CCYYYYYCC16. CAGE INSTALLATION VZZV